







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterWhat Wrought Iron Fence Cost Looks Like in Allen, TX
Wrought iron fence cost in Allen, TX runs $45-$75 per linear foot installed for standard 4-ft ornamental iron or steel picket, and $65-$95 per linear foot for 6-ft privacy-height panels. Most residential jobs here land between $3,500 and $9,000 all-in. Those numbers hold up only if the post bases are specified for Allen’s blackland clay, and that’s the cost variable almost every quote you’ll get leaves out. Call Groundwork Construction Co. of Allen at (888) 343-9048 for a free estimate with the corrosion spec written into it.

Why Allen’s Clay Makes This Fence Cost More Than a Catalog Quote
Walk any fence line in Bethany Ridge or a corner lot off Exchange Parkway and you can read the soil. Blackland clay holds moisture at the post base through the whole year. Down in sandy ground, a post dries out by July. Here it doesn’t. The base of that fence is sitting in damp soil in spring, summer, fall, and most winters, and bare iron painted with standard black enamel will start showing rust at the ground line in three to five years. Sometimes less where a sprinkler head hits the same spot.
That’s not a cosmetic problem you get to ignore. Once rust starts climbing the picket, the paint around it lifts, water gets behind it, and the failure accelerates. By the time a homeowner in Allen calls us about it, we’re usually looking at full refinishing rather than a touch-up.
The fix is boring and it’s cheap relative to a rebuild: hot-dip galvanized post bases, epoxy primer over the bare iron, then the topcoat. That sequence adds about $3-$6 per linear foot to the installed price. Budget competitors skip it because it isn’t visible on the day of install. It’s the difference between a fence that’s still holding paint in 2040 and one that’s a rust complaint by 2032.
Wrought Iron Fence Cost Breakdown for Allen Homeowners
Here’s what the Allen market actually prices at. Ranges reflect standard panel systems, terminations, gates, and the corrosion spec described above.
| Line item | Installed range |
|---|---|
| Standard 4-ft ornamental wrought iron or steel picket | $45-$75 per linear foot |
| 6-ft privacy-height wrought iron panels | $65-$95 per linear foot |
| Custom forge work (arches, scroll detail, custom finials) | adds $20-$40 per linear foot |
| Hot-dip galvanized post base + epoxy primer spec | adds $3-$6 per linear foot |
| Typical full residential project | $3,500-$9,000 |
A typical Allen front-yard run of 60 to 90 feet with a matching gate is where most of that $3,500-$9,000 band sits. Corner lots cost more because they have more fence line to protect, and that’s a real number homeowners in Twin Creeks learn the hard way after they’ve already budgeted for a back fence.

Tubular Steel or Wrought Iron? It Changes What You’re Paying For
Most of what’s sold as “wrought iron” in Allen is ornamental tubular steel. True wrought iron is a hand-forged product now made by a small number of shops, and the price reflects it. That’s not a bait-and-switch; it’s the market. The practical consequence is that the corrosion treatment matters more for tubular steel than it does for genuine wrought iron, because the steel tube has a hollow interior that traps moisture at every seam and every post cap.
Before you sign anything, ask three things:
- Is this genuine wrought iron or ornamental tubular steel, and what gauge is the wall?
- Are the post bases hot-dip galvanized, or are they painted bare steel?
- What primer is going on before the topcoat, and is that primer epoxy?
If a bid can’t answer those three in the quote, the price is telling you something. A $40-per-foot bid that skips the galvanizing is cheaper on paper and cheaper-built in the ground. Our Fence Installation crews spec all three as standard, which is why you’ll see them named on the estimate rather than in a verbal promise.
Matching Wrought Iron to Allen’s HOA Review Process
Allen’s master-planned subdivisions were largely built in a single wave through the 1990s and 2000s, and the architectural review committees that came with them are still active. Front-yard and corner-lot fence work almost always triggers an ARC pre-approval before the city permit goes through. Wrought iron tends to clear those reviews faster than other materials because it lines up with the traditional and Tudor character those neighborhoods were designed around.
We’ve seen the opposite too: a vinyl privacy fence proposed for a front corner in one of the Bethany Ridge sections that sat in review for weeks while the homeowner waited. It isn’t a knock on vinyl, it’s just that wrought iron matches the architectural intent and the committees know it. If you’re still weighing materials for a side or rear run, our Fence Installation in Allen page walks through the comparison, and our home page shows the full range of work we take on across Allen.
One operator detail worth knowing: the ARC submission usually needs the elevation drawing and the color spec at the same time the city permit application goes in. When those two documents drift apart, the job stalls. We coordinate them together so the fence doesn’t sit half-approved while the yard gets measured twice.
What the 730-Day Done Right Promise Covers on a Wrought Iron Fence
Surface rust showing up within two years of installation is a prep failure, not normal weathering. On a properly primed and galvanized base in Allen’s clay, you shouldn’t see ground-line rust for a decade or more. If it shows up early inside our coverage window, we refinish and re-treat it at no cost to you under the 730-Day Done Right Promise. That’s the guarantee in writing, not the handshake version.
Our technicians have up to 12 years of experience, they’re background-checked and arrive in uniform, and the pricing is upfront: the number on the estimate is the number you pay. Calls reach a live person around the clock. On larger projects over $10,000 we also offer 0% financing for 18 months and $1,000 off, which usually matters more on a full perimeter job than a single front run.
FAQs
Plan on $45-$75 per linear foot for standard 4-ft ornamental iron and $65-$95 per linear foot for 6-ft privacy panels, with most Allen homes landing between $3,500 and $9,000 for a full run. Custom forge work adds $20-$40 per linear foot, and the galvanized-base corrosion spec adds $3-$6 per linear foot. Call (888) 343-9048 for an exact quote; estimates are free.
A properly specified fence in Allen’s blackland clay should hold its finish 15 to 20 years before it needs refinishing, provided the post bases are hot-dip galvanized and the iron was epoxy-primed before the topcoat. Bare steel painted with standard enamel at the ground line can start rusting in three to five years. The spec, not the material label, is what determines the lifespan. Call (888) 343-9048 and we’ll walk you through what’s going in your yard.
No, wrought iron costs more per linear foot than either, and that’s before the corrosion spec. Cedar privacy fence runs in a lower band and vinyl sits in our Fence Installation in Allen pricing at $3,500-$9,000 installed, which overlaps the low end of wrought iron but doesn’t buy the lifespan. The argument for iron is durability and HOA fit, not the entry price. Call (888) 343-9048 for a side-by-side on your yard.
In most Allen subdivisions, yes, and often faster than they’ll approve other materials because iron matches the traditional and Tudor architectural intent the neighborhoods were built around. You still need ARC pre-approval before the city permit, and the elevation drawing and color spec need to line up. Call (888) 343-9048 and we’ll coordinate both submissions together.
Get Your Wrought Iron Fence Priced Right the First Time
A wrought iron fence in Allen is a 20-year decision, and the difference between a $40-per-foot bid and a $55-per-foot bid usually lives entirely in the soil at the post base. Get a written estimate with the galvanizing, the epoxy primer, and the topcoat all named, backed by the 730-Day Done Right Promise. Call Groundwork Construction Co. of Allen at (888) 343-9048 for a free estimate and design consult.
Written by the team at Groundwork Construction Co. of Allen, serving Allen, TX.
What Our Customers Say
"Change orders were written down and priced before the work happened, every single time. No surprise at the end."
- Keisha Robinson"He told me one part of what I wanted was a bad idea structurally and offered an alternative instead of just taking the money."
- Angela Wong"The schedule he gave me at the start was accurate to within four days on a three month job. Anyone who has done a renovation knows how unusual that is."
- Laura Bennett












