







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in Murphy, TX: What You’re Actually Getting
Concrete driveways and concrete work in Murphy, TX typically run $4,500 – $12,000 for a full driveway installation, with most jobs finishing in 3 to 6 working days from demo to drive-on, weather permitting. Slabs, aprons, walkway tie-ins, and small flatwork additions usually land between $1,000 and $4,500. Call (888) 343-9048 for a free on-site estimate with a written line-item quote before any work starts.
From First Cut to Final Saw Cut: How We Pour Concrete in Murphy

Concrete is not a one-day trade. The pour is the shortest part of the job. Here’s the actual sequence, so you know what to expect on your lot and when you’ll be asked to make a decision.
Day 1: Site walk, layout, and utility locate
We start by marking the driveway footprint with paint and stakes, then calling in the utility locate through Texas 811. This is non-negotiable. On built-out Murphy lots, the water and gas service lines and any irrigation run right through the work zone, and a cut line on a 1990s plat is not where the plan shows it. You’ll confirm the driveway width and any flare or apron shape at this stage.
Days 1 – 2: Demo, haul-off, and subgrade prep
Old concrete, root-bound soil, and any failing base come out and get hauled away. We rough-grade the subgrade, then compact it in lifts and verify slope away from the garage and the house. This is where your grading decision matters: North Texas black clay pushes water around after a storm, so we set fall to daylight or to a drainage path you approve. Typical demo and prep on a two-car drive: 1 to 2 days.
Day 2: Forming, base, and rebar
We set forms, spread and compact the crushed base, and tie the rebar grid. This is your moment to confirm thickness (4 inch is standard; 5 to 6 inch for heavier loads) and whether you want control joints laid out to match an HOA pattern. Most Murphy subdivision plats and HOAs have an approved width and finish. We walk the form with you before we pour.
Day 3: The pour and finish
Concrete arrives and gets placed, screeded, floated, and finished. Broom finish is standard and safe in wet weather; a light exposed-aggregate or salt finish costs more but stays gripping and hides tire marks. Control joints go in same-day. The pour itself is a few hours on a typical drive.
Days 3 – 6: Cure, joint seal, and drive-on
Concrete needs to cure before it takes a loaded truck. Foot traffic is usually fine the day after the pour; vehicles generally after 5 to 7 days depending on heat and mix. We handle the joint seal and a final walkthrough, then hand you the paperwork on the 730-Day Done Right Promise. If your job is part of a full Driveway & Pavers in Murphy scope, we sequence the flatwork around the pavers so nothing gets poured twice.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Concrete Options You’ll Actually Choose Between
Concrete is not one product. Here are the real choices on a Murphy driveway and what each one costs you in money, durability, and upkeep.
- Standard broom-finish slab (4 inch, rebar): The default. Best value, handles Texas heat and traffic, and one of the least expensive to install. Trade-off: reveals tire marks and hairline cracks over time.
- 5 to 6 inch slab with heavy rebar: Better for a wide drive, RVs, or a lot with a slope. Costs a bit more in concrete and labor, but resists cracking on black clay.
- Exposed aggregate or salt finish: Adds grip and hides marks. Higher upfront cost, holds up well in wet weather. Good if your driveway slopes.
- Colored or integral dye concrete: Matches brick or stone on a 1980s – 2000s Murphy home without the paver budget. Trade-off: color fades unevenly if the mix isn’t consistent, so it pays to use a single pour.
- Pavers set in concrete: The premium end. More expensive and more labor, but easy to repair and timeless on the curb. Our Driveway & Pavers service covers the paver route if you want to compare finishes.
On materials, we spec brands we trust on the flatwork side too: Atlas and Tamko show up in our exterior work, and the concrete mix and base we source is graded for North Texas clay. The brand on the bag matters less than the mix design and the base compaction, and we’ll show you both on the quote.
What Concrete Driveways & Concrete Work Costs in Murphy, TX

Concrete Driveways & Concrete Work in Murphy runs $4,500 – $12,000 for a full driveway installation, and $5,000 – $14,000 when an existing drive is torn out and replaced. Small flatwork, aprons, and utility pads typically land in the $1,000 – $4,500 range. Here’s what moves the number.
- Square footage: A single-car drive sits near the low end; a wide three-car with a turnaround pushes toward the top.
- Existing condition: Old concrete, tree roots, or a failing base means more demo and haul-off.
- Utilities and grading: Relocating a water line, irrigation, or dealing with tight-lot drainage in an already-developed Murphy plat adds cost.
- Finish and thickness: Exposed aggregate, color, or a 6-inch structural slab costs more than broom finish at 4 inch.
- Permit scope and HOA approval: Some Murphy jobs need a permit and plat review; we pull it and pass inspection.
Every written estimate is line-item: demo, base, rebar, concrete, finish, permit, and haul-off are all spelled out. The number you see is the number you pay. No change orders unless you ask for a change. Pricing is upfront, and 0% financing for 18 months is available, plus $1,000 off projects over $10,000. Estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Murphy Homes Specifically Do to This Job
Murphy is essentially built out. There’s almost no vacant land, which means almost every concrete driveway job we do here is infill, teardown-rebuild, or renovation on lots platted in the 1980s through the 2000s. That changes the work. On a greenfield build in an exurb, you pour on open ground. In 75094, you pour between an existing fence, an established tree canopy, and a neighbor’s driveway six feet away, and the original plat’s setbacks, easements, and drainage patterns dictate the whole job. Permits and inspections run through a small-town development services department, not a big-city one, and HOAs on the older plats have approved widths and finishes you’ll want to check before you pour.
The soil does its part too. North Texas black clay expands and contracts with our wet-dry cycles, and a Tarrant County summer bakes a slab every August. That’s why base compaction and joint layout matter here more than in drier markets, and why we over-build the base on lots we know are clay-heavy. Hail and wind aren’t a driveway problem, but they’re the reason some Murphy homeowners plan exterior work as one package: homeowners often pair this with ADU Site Prep & Utilities in Murphy when a backyard build needs a new approach and utility runs, and we handle the flatwork on both. If you’re updating the exterior at the same time, some homeowners also pair concrete flatwork with Door Installation in Murphy.
Serving Murphy, TX – Our Local Coverage Area
We serve Murphy and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Concrete Driveways & Concrete Work in Murphy

A standard two-car concrete driveway in Murphy takes 3 to 6 working days from demo to drive-on, weather permitting. The pour itself is a few hours; the rest is prep, forming, and cure time. Call (888) 343-9048 to schedule a free estimate and get a real timeline for your lot.
Most Murphy driveway and flatwork jobs require a permit, and some plats require HOA approval on top of that. We pull the permits and pass inspections as part of the job. Call (888) 343-9048 and we’ll confirm what your specific address needs.
In most cases, yes. Concrete flatwork sits on grade, so we usually pour around existing utilities without touching plumbing or structure. If a line runs through the work zone, we coordinate the locate and adjust. Call (888) 343-9048 for an on-site look.
Concrete Driveways & Concrete Work in Murphy costs $4,500 – $12,000 for a full driveway, and $5,000 – $14,000 for a tear-out and replacement. Small flatwork runs $1,000 – $4,500. Call (888) 343-9048 for an exact quote, and estimates are free.
Every concrete driveway and flatwork job we do in Murphy is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That horizon is longer than most workmanship guarantees in the space. Call (888) 343-9048 to talk through what’s covered.
Get a Free Concrete Estimate in Murphy
Concrete Driveways & Concrete Work in Murphy starts with a free on-site estimate. Call (888) 343-9048 and a live person answers, day or night. We’ll walk the lot, check the utilities and drainage, measure the square footage, and hand you a written line-item quote with the permit and haul-off included. No pressure, no surprise numbers. Our technicians have up to 12 years of experience, and we cover Murphy and the surrounding Collin County communities.
Written by the team at Groundwork Construction Co.












