







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterVanities, Tile & Fixtures in Allen, TX
Vanities, tile and fixtures are the three elements that decide whether a bathroom feels finished or half-done. The vanity anchors the room, the tile sets its character and protects the wet zones, and the fixtures (faucets, showerheads, drains, lighting) are what you actually touch every day. Get all three right and a modest Allen bathroom reads like a custom build. Get them wrong and you’re living with a wobbly cabinet, cracked grout lines and a faucet that drips into the night.
Groundwork Construction Co. of Allen handles vanities, tile and fixtures as part of full Bathroom Remodeling, which means one crew owns the plumbing rough-in, the substrate, the set, the grout and the final trim. No coordinating a tile guy who won’t talk to the vanity installer. Our technicians have up to 12 years of experience, and every project is covered by the 730-Day Done Right Promise. Call (888) 343-9048 and a live person picks up, day or night.
If you’re weighing a tile-and-fixture refresh against a full gut, start with our Bathroom Remodeling in Allen page, then come back here for the details on the finishes.
Key Takeaways
- Vanity, tile and fixture work in Allen typically runs $4,200 to $16,500 depending on scope, tile selection and whether the layout moves.
- Tile substrate, waterproofing and slope matter more than the tile itself. We don’t skip the membrane.
- We work with Moen, Delta and American Standard fixtures because parts are stocked locally and service is real, not theoretical.
- Most vanity swaps and fixture replacements finish in a single visit; full tile surrounds run 3 to 7 days.
- 0% financing for 18 months and $1,000 off projects over $10,000 are standing offers, not seasonal promotions.

When You Need Vanities, Tile & Fixtures
Allen homeowners call us for a handful of recurring reasons. Most aren’t emergency calls, but they’re the kind of thing you notice every single morning.
- Your vanity is sagging or the cabinet box is swollen. Particleboard vanities in Allen’s older 1990s and early-2000s builds absorb humidity from daily showers. Once the box swells, no amount of caulk fixes it. You need a replacement, ideally plywood or a moisture-rated composite.
- The grout lines in your shower have gone dark or started crumbling. North Texas water is hard, and Allen’s supply runs on the harder side. That means mineral buildup in grout and around fixture bases. Crumbling grout is a warning sign that water is getting behind the tile, and that’s a substrate problem, not a cleaning problem.
- A faucet drips, a shower valve won’t hold temperature, or the finish has flaked off. Delta and Moen cartridge failures are common after 10 to 15 years. Sometimes it’s a $40 cartridge. Sometimes the valve body itself is shot and it’s a wall-open repair.
- You’re updating before listing or after buying. Buyers in Allen’s $400K to $700K range look hard at primary bathrooms. A dated vanity with a cultured marble top and a brass-framed shower door reads as a deduction on the inspection report.
- Your shower pan is leaking into the ceiling below. In two-story homes around Bethany Ridge and Watters Crossing, a stain on the first-floor ceiling is often a failed pan liner upstairs. That’s a tile-out, membrane-in job, and it needs a pro.
- You want a freestanding tub, a curbless shower or a double vanity where there was a single. Layout changes mean moving the drain, relocating supply lines and rethinking the floor tile pattern. That’s a permit-and-plumbing conversation.
Anything involving a shower pan, valve body or relocated drain is a professional job. Tile work over a bad substrate fails in 18 months no matter how pretty the set looks on day one, and water damage behind a wall in Allen’s climate, with our humid summers and occasional hard freezes, gets expensive fast. We’d rather tell you the truth about what’s behind the tile than sell a surface fix.
Our Vanities, Tile & Fixtures Process
Here’s how a vanity, tile and fixture project actually runs when we’re on it.
- Walkthrough and measurements. We measure the vanity alcove, check the plumbing wall, confirm whether the drain and supply lines can stay put, and look at the floor structure. If you’re in a pier-and-beam home, we check for deflection before we commit to large-format tile.
- Material selection. You pick the vanity, countertop, tile and fixtures with us in the room, not from a catalog in a hurry. We’ll tell you what holds up: porcelain over marble in a shower floor, a Moen or Delta valve with a replaceable cartridge, American Standard or Kohler for the toilet if you’re replacing it while the floor is open.
- Demo and rough-in. Old vanity out, old tile down to the studs, old valve replaced. If the layout moves, we pull the permit. We inspect the framing and subfloor while the wall is open, because that’s the only cheap moment to fix rot.
- Substrate and waterproofing. Cement board or a foam board system, then a liquid or sheet membrane on the shower walls and a properly sloped pan. This is the step nobody sees and the one that determines whether the job lasts.
- Tile set, grout and seal. Layout planned from the room’s sight lines, not from a corner. Full cure before grout, full cure before seal. Epoxy grout where you want the least maintenance.
- Vanity set and fixture trim. Cabinet leveled and shimmed, top set, faucet and drain installed, shower trim and valve handle on, toilet reset, caulk lines run clean. Then we walk the room with you and don’t leave until it’s right.
Most vanity swaps and fixture-only jobs finish in a single visit. A full tile shower with new pan and valve runs 3 to 7 days. We tell you which one you’re getting at the estimate, and the number you see is the number you pay.

Vanities, Tile & Fixtures Pricing in Allen
Here are honest ranges for Allen. These reflect what we actually see in homes around Twin Creeks, Bethany Lakes, Watters Crossing and the older stretches near downtown Allen. Tile and fixture selections move the number more than labor does.
| Scope | Typical range | What drives it |
|---|---|---|
| Vanity replacement only (cabinet, top, faucet) | $1,200 – $3,800 | Cabinet size, whether plumbing moves, countertop material |
| Fixture swap (faucets, shower trim, toilet) | $650 – $2,200 | Number of fixtures, valve condition, finish tier |
| Floor tile only | $1,400 – $4,200 | Square footage, tile format, substrate condition |
| Tub or shower surround tile | $2,800 – $7,500 | Waterproofing method, tile size, niche and bench |
| Full vanity, tile and fixture package | $4,200 – $16,500 | Layout changes, permit, glass, freestanding tub |
What moves you toward the top of a range: layout changes (moving the drain or supply lines), a failing shower pan that needs a full rebuild, large-format porcelain or natural stone, frameless glass, and any hidden rot behind the wall. What keeps you low: same-footprint vanity swaps, keeping the existing valve, and ceramic tile in standard sizes.
Upfront pricing, no surprises. We measure, we quote, and the number holds. Calls are answered by a live person 24/7. Standing offers apply: 0% financing for 18 months, a free project estimate and design consult, and $1,000 off projects over $10,000.
FAQs – Vanities, Tile & Fixtures
How much does a bathroom vanity replacement cost in Allen?
A vanity replacement in Allen typically runs $1,200 to $3,800 installed, including the cabinet, countertop and faucet. The range depends mostly on cabinet size, whether the plumbing stays put, and whether you go with a stock vanity or a semi-custom unit. Call (888) 343-9048 for an exact quote. Estimates are free.
Can you replace a shower valve without tearing out the whole bathroom?
Sometimes, yes. If the valve is accessible from an adjacent closet or through a small opening, we can swap it with minimal tile disruption. If the valve body is buried behind the shower wall, the honest answer is that the tile around it comes out and gets patched. We’ll tell you which scenario you’re in after looking, not before. There is no safe DIY path through a live valve body, so let a trained professional handle it. Call (888) 343-9048 and we’ll walk you through it.
How long does tile work take in an Allen bathroom?
A shower surround typically takes 3 to 5 days from demo to sealed grout, and a floor adds 1 to 2 more. The schedule is driven by cure times, not by how fast we can lay tile. Rushing grout over wet thinset is how jobs fail. Call (888) 343-9048 for a realistic timeline on your job.
Is it cheaper to repair or replace a shower pan?
Repairing a failed shower pan almost never makes financial sense once water has reached the substrate. A patch buys you a few months. A full pan rebuild with new membrane and slope costs more upfront but is the only path that lasts. In Allen’s clay soils, a small leak under the slab or into the ceiling cavity gets expensive quickly, so we recommend rebuilding rather than patching. Call (888) 343-9048 for a free assessment.
Ready to stop living with a dripping faucet and a dated vanity? Call (888) 343-9048 today for a free estimate and design consult. A live person answers, any hour, and we’ll get a technician out to look at your Allen bathroom. If you’re mapping out a bigger project, look at our home page and see the full range of work we do across Allen and the surrounding markets.
Written by the team at Groundwork Construction Co. of Allen, serving Allen.


