







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Fairview, TX: What the Job Actually Involves
Asphalt driveways & resurfacing in Fairview, TX usually run $3,500 to $9,000 for a full paving job, and a seal-and-resurface refresh on an existing drive typically lands between $250 and $700 per pass. The work itself is two to three days from tear-out to a drivable surface, plus a cure window before you park heavy vehicles on it. If you want a real number instead of a ballpark, call (888) 343-9048 and we’ll set up a free on-site estimate.
How a Fairview Asphalt Driveway Comes Together, Stage by Stage

Asphalt is not a pour-and-leave material. Every good drive here starts underground and works up. Here’s the honest sequence, and where you’ll be making decisions.
Stage 1: Site visit and layout (about 60 – 90 minutes)
We walk the drive, measure width and slope, and check where water currently runs. On the large wooded lots common in Fairview, that means looking hard at tree roots and drainage away from the slab. You decide the final driveway footprint and whether we’re going over an existing asphalt base or starting fresh. If the drive ties into a courtyard turnaround or a detached garage pad, that gets measured now too.
Stage 2: Tear-out and grading (day 1, 4 – 8 hours)
Existing asphalt, failed base, and soft subgrade come out. With North Texas blackland clay underneath, we re-grade and compact in lifts so the base doesn’t pump and create the rutting you see on drives laid thin. You’re not deciding anything here except where the excavated material goes (usually off-site). This is the stage that separates a 12-year drive from a 25-year drive.
Stage 3: Base and stone (day 1 into day 2)
A compacted crushed-stone base goes down, typically 4 to 6 inches depending on whether cars or heavier vehicles will use it. On Fairview lots with mature oaks and pecans near the drive edge, we keep equipment off the root zones and protect what the tree-preservation rules on these properties care about. You confirm base thickness and edge restraint type at this point.
Stage 4: Hot-mix asphalt (day 2, half a day)
Hot asphalt is laid at roughly 2 to 3 inches compacted over the base for a residential drive, rolled while it’s still hot. You choose the grade of mix and whether you want a binder-and-surface two-course build (better on soft clay) or a single course. The edge is compacted and the transitions at the apron are finished before the crew leaves.
Stage 5: Cure, seal and final walk (3 – 7 days of cure, then a walkthrough)
No parking for about three days, light traffic after a week in warm weather. We walk the finished drive together, mark anything that needs attention, and hand you the warranty in writing. A first seal coat is usually scheduled after the asphalt has fully cured, not on day one. That final walk is also where you decide whether you want a periodic reseal program, which is where the $250 – $700 per pass lives.
Throughout, our technicians have up to 12 years of experience, and every job is backed by the 730-Day Done Right Promise. Our driveway & pavers service handles the wider surface work if you’re also thinking beyond the drive, and the team behind it is broader than asphalt alone.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Your Real Choices When You Order the Drive
- Asphalt grade and thickness. A 2-inch single-course drive is the budget option and suits a light-use side drive. A 2.5- to 3-inch two-course build costs more up front but handles the clay movement far better and lasts noticeably longer.
- Base depth. 4 inches of compacted stone is the minimum on solid ground. On the soft spots that show up on older Fairview estate drives, 6 inches of base prevents the rutting that a cheap base guarantees within two years.
- Edge restraint type. Concrete curbing stones hold the asphalt edge and keep it from raveling; wooden edge stakes are cheaper but fail sooner. Add crushed stone shoulders if you park on the edge.
- Resurface vs. full rebuild. If your current asphalt is just oxidized and lightly cracked, a resurface plus seal saves the base and money. If it’s rutting or spider-cracked from failed subgrade, a resurface is money spent twice, and a rebuild is the honest answer.
- Seal coat schedule. A good asphalt drive wants sealing every two to three years. It runs $250 – $700 each time and is the single cheapest way to extend the life of the surface.
What Asphalt Driveways & Resurfacing Costs in Fairview, TX

For a typical Fairview residential drive, full asphalt paving runs $3,500 to $9,000, a resurface of an existing base runs in the $250 to $700 range per pass, and a full replacement drive is $5,000 to $14,000. Here’s what actually moves you to the low or high end of that:
- Drive size. A standard 12-foot-wide, 40-foot-long drive sits on the low end. The long, curved, multi-car drives on the large Fairview lots push toward $9,000.
- Existing condition. A clean, usable base keeps you toward $3,500. A failed base, soft clay, or bad drainage pushing a full rebuild moves you toward the replacement range.
- Base preparation. Extra stone, over-excavation on soft spots, and regrading all add to the number. We list them in the estimate so nothing surprises you.
- Access and tree protection. On wooded lots, staging equipment around mature oaks and protecting root zones takes time and adds cost. We tell you up front if it does.
- Permit scope. Fairview projects that touch the right-of-way or change drainage may need permits, and those are separate from the paving cost in the estimate.
A written estimate from us is line-item: base, asphalt, edges, seal, and any permit allowance. What’s often not included elsewhere: driveway replacement of a failing base (that’s a full replacement, $5,000 – $14,000), and any landscaping repair where equipment had to stage. We price those separately so you see exactly what you’re paying for. No-hassle upfront pricing means the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhy a Fairview Drive Is a Different Build
Fairview is one of the few Collin County towns where new custom construction on large, heavily wooded lots routinely triggers tree-preservation and setback review, and mature oaks and pecans have to be designed around rather than cleared. Driveway work here follows the same logic: staging equipment around a canopy and keeping the root zones intact is a step we plan for before the crew arrives, and it’s rarely a factor in a newer, cleared subdivision in Allen or McKinney. Homeowners pairing this with an accessory structure often work it into the same schedule as ADU Site Prep & Utilities in Fairview, since shared utility runs and grading decisions line up. Fairview’s blackland clay is the other variable. It shrinks and swells with the wet-and-dry cycle, so a compacted base and decent thickness aren’t optional niceties, they’re the reason the drive outlasts the weather. The housing stock is mostly custom single-family homes on one-plus-acre lots built from the 1990s through the 2010s, with a steady stream of tear-down rebuilds and additions, and those drives are typically wide, long, and open to the sun. Summer heat and hail also stress the binder and the seal, which is why we set up a reseal schedule on day one. When the drive is part of a larger site project, it lives inside our Driveway & Pavers in Fairview scope, and Fairview is one of the communities we cover through our Fairview service area.
Serving Fairview, TX – Our Local Coverage Area
We serve Fairview and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Asphalt Driveways & Resurfacing in Fairview

Two to three days from tear-out to a drivable surface, with a cure window of about three days before parking and a week before heavy use. On wooded lots with staging constraints, add a day. Call (888) 343-9048 for a schedule based on your property.
For a straightforward replacement on your own property, usually not. For anything that touches the right-of-way, changes drainage, or is part of a larger addition or accessory structure, permits and inspections apply, and we handle pulling them. Call us and we’ll tell you exactly where your project stands.
It depends on the base. If the asphalt is oxidized and the base is sound, a resurface and reseal is the right call at $250 – $700 per pass. If the drive is rutted or spider-cracked from failed subgrade, a full replacement ($5,000 – $14,000) is the honest answer, because a resurface over a bad base fails fast. Call (888) 343-9048 and we’ll look at it and tell you straight.
No. With our upfront pricing, the number in your written estimate is the number you pay, and any change you request is quoted and approved before we touch it. If you’re pairing the drive with perimeter work like Chain Link Fence in Fairview, we quote both together so there’s no surprise. Call for a written estimate.
All of our asphalt workmanship is covered by the 730-Day Done Right Promise: if it isn’t done right, we make it right. Our technicians have up to 12 years of experience, and calls are answered by a live person 24/7. Call (888) 343-9048 to get started.
Get a Free Asphalt Driveway Estimate in Fairview
Call (888) 343-9048 to schedule a free on-site estimate for asphalt driveways & resurfacing in Fairview. A live person answers, day or night, and we’ll walk your drive, measure it, and hand you a line-item written quote with base, asphalt, edges, sealing and any permit allowance spelled out. You’ll know the number before you commit. Proudly backed by the 730-Day Done Right Promise and our $1,000 off projects over $10,000.
Written by the team at Groundwork Construction Co.












