







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Garland, TX: What It Costs and How Fast
A chain link fence in Garland, TX typically runs $3,500 to $9,000 for a standard residential lot, with most single-family jobs landing between $4,200 and $6,800. A straightforward 150-foot run with a drive gate takes one to two working days once posts are set. Call (888) 343-9048 for a free on-site estimate. We’ll walk the property line with you, flag the setbacks that matter on an older Garland lot, and leave you with a written line-item number, not a range scribbled on a business card.
How we build a chain link fence, start to finish

The sequence on a chain link job is fixed and predictable, which is why the good crews finish in days, not weeks. Here’s what actually happens on your property.
Stage 1: Site walk and layout (same day as the estimate, or day one). We mark the run, confirm property lines against your plat, and check for irrigation lines, gas risers, and the pool equipment pad that older Garland yards tend to hide along the fence line. You decide gate placement here: a single 4-foot walk gate, a double drive gate, or both. This is the decision that most affects the final number, so make it early.
Stage 2: Utility locate and permit (day one to day three). We call for locates before anyone digs. On Garland properties from the 1950s and 1960s, we’ve learned to also hand-probe near the back corner, because original service laterals don’t always run where the aging plat drawing says. If your fence sits close to a setback line or crosses an easement, we pull the permit with the city and wait for the locate window. That’s usually a two-to-three day pause you can’t compress. You decide whether to hold the line at the plat boundary or bump in two feet for a wider mow strip.
Stage 3: Demo and post setting (day two to day four). Old fence comes out, including the concrete footings, which are the slow part. We set terminal posts and gate posts in concrete, deeper and larger than line posts, then set the line posts. Posts cure overnight on most residential runs. This is the stage where the Crew Lead photographs the hole depths so you have a record.
Stage 4: Rails, fabric, and gates (day three to day five). Top rail goes up, the chain link fabric is stretched and tied, and prefabricated or fabricated gates are hung and adjusted for swing. Stretch tension is the difference between a fence that stays tight for a decade and one that sags by spring. You inspect gate swing and latch height here before we close out.
Stage 5: Tie-off and walkthrough. Tension wire at the bottom, tie wires on every post, and a final walk with you. We haul off all old material the same day.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices that actually matter on a chain link fence
Chain link looks like a commodity until you price out a cheap job against a right one. Five decisions drive the outcome:
- Gauge and coating. 11.5-gauge galvanized is the standard residential fabric. 9-gauge is heavier and resists dog pressure and ball impacts better on a Garland backyard where kids actually play. Vinyl-coated fabric adds roughly 15 to 25 percent to material cost and gives you color options, but the coating chips at the bottom rail over time in our hail-prone climate.
- Post schedule. Line posts every 10 feet with the top rail and tension wire are standard. Push to 8-foot spacing on a heavy-use dog run, and consider a bottom tension wire where the soil moves, since clay contraction can leave a gap under the fabric.
- Height. 4 feet is common for a garden edge; 6 feet is the norm for property line privacy and pool code. 7 and 8 feet exist and cost more per foot because post gauge and concrete volume climb.
- Gate type and operator. A walk gate is simple. A drive gate wide enough for a truck needs heavier posts and a truss rod, and if you want it automated, the fence line has to accommodate the operator arm and the safety loop, which is often a separate trench. If you want a rolling gate for a narrow drive, expect custom fabrication.
- Top rail and finish. A full top rail is standard. Colors range from plain galvanized to black, brown, or green. We can source matching brand-family hardware, and where a homeowner wants something heavier at the street, we sometimes frame a short decorative section in Tamko-matching powder coat so the front of the house doesn’t read as industrial.
What a Chain Link Fence costs in Garland, TX

Residential chain link in Garland runs $3,500 to $9,000 for the typical job. Here’s how the range breaks down:
| Line item | Typical range |
|---|---|
| 6-foot galvanized, 150 linear feet, one walk gate | $4,200 – $6,200 |
| 4-foot garden or boundary run, 100 feet | $3,500 – $4,800 |
| Double drive gate with heavy posts | Add $900 – $1,800 |
| Vinyl-coated fabric, color match | Add 15% – 25% |
| Demo and haul-off of existing fence | $400 – $1,100 |
Four variables push a job to the high end. Run length is the biggest. Existing condition matters next: an old fence with deep concrete footings costs more to remove than one set in clay. Terrain and access come third, and a sloped Garland backyard with a tight side gate adds labor. Gate complexity is fourth. Finally, permit scope, since a fence near a setback or crossing an easement adds paperwork and inspection time.
A written estimate from us lists fabric gauge, post gauge, post spacing, gate count and width, concrete volume, demo, and permit line separately. It does not include landscaping repair, moving irrigation heads, or resodding a disturbed strip unless you ask. The number you see is the number you pay. No change order for materials that showed up the way we planned.
See the difference
Before
After
Before
After
Before
AfterWhat Garland homes specifically do to this job
Garland is a first-ring postwar manufacturing suburb. It grew up around the Kleenex and Raytheon plants, and most of the housing stock inside Loop 12 dates from the 1950s through the 1970s. That means our chain link work here is almost always a replacement or a re-route around an aging single-story brick ranch, not a new-build install on raw land. Down in the 75040, 75041, and 75042 ZIP codes, lots are narrow and fences often run the full depth of the property, so you end up pricing a longer run per property than you would in a newer suburb.
The other thing Garland does to a chain link fence is the soil. Blackland clay under these yards expands in a wet spring and contracts through a dry August, and that movement is what we see stress the fence line. Posts that were fine in March can sit proud by the fall. We oversize footing holes on the back run and add a bottom tension wire wherever the grade suggests a gap forming. Where an existing fence has rusted at the bottom rail and the fabric still has life, we can sometimes repost and re-tension without replacing fabric, which saves money. Where the whole line is failing, replacement is the right call and lands in the $3,500 to $9,000 range.
We work across Garland ZIPS 75040, 75041, 75042, and 75049, and up toward the 75044 and 75043 subdivisions where the housing gets a decade or two newer. Every project carries the 730-Day Done Right Promise. If the fence isn’t right, we make it right.
Serving Garland, TX – Our Local Coverage Area
We serve Garland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Chain Link Fence in Garland

Most residential chain link fences in Garland take one to two working days on site once the permit and utility locate are cleared. The locate window itself can add two to three days, and if you’re near a setback or crossing an easement, add a city review. Call (888) 343-9048 and we’ll give you a realistic start date, not a hopeful one.
It depends on height, location, and whether the fence sits along a street or in an easement. A 6-foot rear privacy run on an interior lot is often straightforward; a 7-foot run or a fence near the front setback typically needs review. We check the current city rules against your specific lot before we order material. Call (888) 343-9048 and we’ll tell you exactly what applies to your address.
Yes. On most Garland properties the fence line sits in a narrow strip, and our crews hand-dig where irrigation or pool plumbing is flagged. We don’t move the pool or rework the yard, but we do call for locates and probe the corners where old laterals are likely buried.
Residential chain link in Garland runs $3,500 to $9,000, with a typical 6-foot run and one walk gate landing between $4,200 and $6,800. A double drive gate, vinyl coating, or heavy demo pushes the job toward $9,000. Call (888) 343-9048 for a free on-site estimate with a written line-item number.
Every chain link fence we install is covered by our 730-Day Done Right Promise. That’s two full years on workmanship, which covers post setting, tension, and gate adjustment. Material coverage comes separately from the manufacturer. Call (888) 343-9048 if anything isn’t right and we’ll come back out.
Yes, and homeowners often pair this with a room addition or detached structure that needs its own utilities run. If the fence is part of a full Fence Installation in Garland plan, or you’re adding a detached garage, we sequence the fence so it doesn’t get in the way of the build. If you need a slab or utility tie-in for a backyard unit, our ADU Site Prep & Utilities in Garland team works alongside. And where an old garage or shed door is failing at the same time, our Door Installation in Garland service handles it.
Get a free chain link fence estimate in Garland
Every Garland estimate starts with a walk of your property line and a written line-item number for the exact run, gate count, and gauge you choose. We answer the phone with a live person, 24 hours a day, and our technicians arrive background-checked and in uniform. Call (888) 343-9048 to schedule your free estimate, or ask about our Fence Installation service and the $1,000 off on projects over $10,000.
Written by the team at Groundwork Construction Co.












